How to Bypass Chevy Ignition Switch in Minutes: 3 Easy Methods

If you own a Chevy truck, you may have encountered a situation where your ignition switch fails to start your vehicle.

This can be frustrating and inconvenient, especially if you are in a hurry or stranded somewhere.

Fortunately, there are some ways to bypass the ignition switch and get your engine running without a key.

A picture showing a chevy ignition switch[photo courtesy: Carpages]
Note that bypassing your ignition switch may compromise your vehicle’s security and safety, as well as void your warranty or insurance coverage.[photo courtesy: Carpages]
In this article, we will show you three easy methods to bypass Chevy ignition switch in minutes, using simple tools and techniques.

Method 1: Hot-Wiring Your Chevy’s Steering Column

One of the most common methods to bypass Chevy ignition switch is to hot-wire the steering column.

This involves connecting the wires that supply power to the ignition system and the starter solenoid, bypassing the switch itself.

To do this, you will need:

  1. flathead screwdriver
  2. a pair of pliers
  3. electrical tape

Here are the steps to follow:

  • Locate the steering column under the dashboard and remove the plastic cover that protects the wiring. You may need to unscrew some bolts or clips to do this.
  • Look for two wires that are connected to the ignition switch. They are usually red and yellow, but they may vary depending on your Chevy model. You can consult your manual or use a multimeter to identify them.
  • Cut the wires and strip about an inch of insulation from each end. Twist the ends together and wrap them with electrical tape. This will supply power to the ignition system and turn on the dashboard lights.
  • Find another wire that is connected to the starter solenoid. It is usually purple, but it may also vary depending on your model. Cut and strip this wire as well.
  • Use the flathead screwdriver to touch the end of the starter wire to the end of the ignition wire. This will activate the starter motor and crank the engine. Be careful not to touch any other wires or metal parts, as this may cause sparks or shocks.
  • Once the engine starts, remove the screwdriver and tape the starter wire to prevent it from touching anything else. You can now drive your Chevy truck normally.

Method 2: Drilling the Lock Pins

Another method to bypass Chevy ignition switch is to drill out the lock pins that hold the cylinder in place.

This will allow you to remove the cylinder and access the switch directly.

To do this, you will need:

  1. drill
  2. drill bit
  3. hammer
  4. chisel

Here are the steps to follow:

  • Insert the key into the ignition slot and turn it to the “on” position. This will align the lock pins with the cylinder.
  • Use the drill and drill bit to make a hole in the center of each lock pin. You may need to apply some pressure and patience, as the pins are made of hardened steel.
  • Use the hammer and chisel to knock out the pins from the cylinder. You may need to wiggle them a bit to loosen them.
  • Pull out the cylinder from the steering column. You should see a metal rod that connects to the switch behind it.
  • Use a flathead screwdriver or pliers to turn the rod clockwise until it clicks. This will start your engine.

Method 3: Powering the Dash

A third method to bypass Chevy ignition switch is to power up the dash directly, without using the switch or cylinder.

This involves connecting a jumper wire from the battery to one of the fuses in the fuse box under the dashboard.

To do this, you will need:

  1. jumper wire with alligator clips
  2. a fuse puller
  3. a test light

Here are the steps to follow:

  • Locate the fuse box under the dashboard and open it. You should see a diagram that shows which fuse corresponds to which function.
  • Use the test light to find a fuse that is hot only when the key is in the “on” position. This will be one of the fuses that control accessories like radio, wipers, or lights.
  • Use the fuse puller to remove this fuse from its slot.
  • Connect one end of the jumper wire to one of its terminals and insert it back into its slot.
  • Connect another end of jumper wire with alligator clip on positive terminal of battery
  • Connect other end of jumper wire with alligator clip on other terminal of fuse
  • This will power up your dash and enable you to start your engine by turning it over with a screwdriver or pliers.

Conclusion

These are some of the methods you can use to bypass Chevy ignition switch in minutes.

However, we advise you to use them only as temporary solutions until you can replace or repair your ignition switch properly.

Bypassing your ignition switch may compromise your vehicle’s security and safety, as well as void your warranty or insurance coverage.

RELATED: How to Remove Ignition Lock Cylinder Chevy Without Key: A Step-by-Step Guide

We hope you found this article helpful and informative. If you have any questions or comments, please feel free to leave them below.

For more interesting and informative content, visit our website.

Leave a Comment