How to Change Thermostat 2008 Chevy Impala in 5 Easy Steps

If you own a 2008 Chevy Impala and you notice that your engine is overheating, your heater is not working, or your check engine light is on, you may have a problem with your thermostat.

How to Save Your Engine from Overheating by Replacing the Thermostat on Your 2008 Chevy Impala:

How does a thermostat work

The thermostat is a device that regulates the flow of coolant between the radiator and the engine.

A picture of the thermostat
A thermostat [photo courtesy: Amazon]
When the engine reaches a certain temperature, the thermostat opens and allows the coolant to circulate and cool down the engine. When the engine is cold, the thermostat closes and prevents the coolant from flowing, so the engine can warm up faster.

A faulty thermostat can cause serious damage to your engine if left untreated.

Fortunately, replacing the thermostat on a 2008 Chevy Impala is not very difficult and you can do it yourself with some basic tools and a new thermostat.

Here are the steps you need to follow to change your thermostat and save your engine from overheating:

Step 1: Gather the tools and materials you need

Before you start, make sure you have everything you need to complete the job. You will need:

  • A new thermostat (you can buy one online or at your local auto parts store)
  • A socket wrench set
  • A flathead screwdriver
  • A drain pan
  • A funnel
  • A rag
  • Some antifreeze

Step 2: Drain some coolant from the radiator

To access the thermostat, you will need to drain some coolant from the radiator.

Make sure your engine is cold before you do this, as hot coolant can burn you.

Locate the drain plug at the bottom of the radiator and place a drain pan underneath it.

Loosen the plug with a socket wrench and let some coolant drain out until the level is below the upper radiator hose.

You don’t need to drain all the coolant, just enough to prevent it from spilling when you disconnect the hose. Tighten the plug back when you are done.

a picture showing the position of the thermostat in a 2008 Chevy Impala [Photo courtesy: Car Guru]
position of the thermostat in a 2008 Chevy Impala [Photo courtesy: Car Guru]

Step 3: Remove the upper radiator hose and thermostat housing

Next, you will need to remove the upper radiator hose that connects to the thermostat housing.

The thermostat housing is a metal part that sits at the end of the hose near the engine block.

To remove the hose, use a flathead screwdriver to loosen the clamp that holds it in place. Then, pull the hose off the housing and set it aside. You may need to twist and wiggle the hose a bit to get it off.

After that, you will need to remove the thermostat housing itself.

There are two bolts that secure it to the engine block.

Use a socket wrench to undo them and then lift off the housing and gasket. You will see the old thermostat inside. Take it out and discard it.

A picture showing a way in which you can access the thermostat using the bottom hose pipe [photo courtesy: MotorTrend]
A way in which you can access the thermostat using the bottom hose pipe [photo courtesy: MotorTrend]
A picture showing the housing of the thermostat after removing the hose pipe [Photo courtesy: MotorTrend]
Housing of the thermostat after removing the hose pipe [Photo courtesy: MotorTrend]

Step 4: Install the new thermostat and gasket

Now, you are ready to install the new thermostat and gasket.

Make sure you buy a compatible thermostat for your 2008 Chevy Impala model.

You can check your owner’s manual or online sources for more information. The new thermostat should come with a new gasket as well.

To install them, first clean the gasket surfaces on both the housing and the engine block with a rag.

Then, place the new gasket on top of the engine block and align it with the bolt holes.

Next, insert the new thermostat into the housing with its spring side facing down. Make sure it fits snugly and securely.

Finally, place the housing over the gasket and bolt it back to the engine block with a socket wrench. Tighten the bolts evenly and firmly.

Step 5: Reconnect the upper radiator hose and refill coolant

The last step is to reconnect the upper radiator hose and refill coolant.

To reconnect the hose, simply slide it over the housing and secure it with its clamp.

Then, use a funnel to pour some antifreeze into the radiator until it reaches its full level.

You may need to squeeze or burp the hose a few times to remove any air bubbles from the system.

You can also run the engine for a few minutes and check the temperature gauge to make sure it is working properly.

If the gauge shows normal readings and you have heat coming from the heater, you have successfully changed your thermostat.

Conclusion:

Congratulations! You have just learned how to change thermostat 2008 Chevy Impala in 5 easy steps. You have saved yourself some money and prevented your engine from overheating. Now, you can enjoy driving your Impala with confidence and peace of mind.

If you enjoyed this article and want to learn more about the  thermostat in 2008 chevy impala, don’t forget to check out our website for more interesting and informative content.

You can also check out these other articles on our blog:

  • How to diagnose a bad thermostat on a 2008 Chevy Impala
  • How to prevent thermostat problems on a 2008 Chevy Impala
  • How to choose the best thermostat for a 2008 Chevy Impala
  • How to save money and time by changing the thermostat on a 2008 Chevy Impala yourself
  • How to troubleshoot common issues related to the thermostat on a 2008 Chevy Impala

Leave a Comment