How to Remove Ignition Lock Cylinder Chevy Without Key: A Step-by-Step Guide

Have you ever lost your car key and wondered how to start your Chevy without it? Or maybe you want to replace your old ignition lock cylinder with a new one, but you don’t have the original key anymore.

Whatever the reason, you might think that removing the ignition lock cylinder from your Chevy without a key is impossible or very difficult.

But don’t worry, it’s not. In fact, there are some simple ways to do it with just a few tools and some patience.

In this article, we will show you how to remove the ignition lock cylinder from your Chevy without a key, and how to start your car without a key as well.

Follow this step-by-step guide and you will be able to get your Chevy running again in no time.

A picture showing part of the ignition lock cylinder[photo courtesy: United Locksmith]
There are two main methods to remove an ignition lock cylinder without a key: using a screwdriver and hammer, or using a drill.[photo courtesy: United Locksmith]

What is an Ignition Lock Cylinder and Why Do You Need to Remove It?

An ignition lock cylinder is the part of your car that holds the key and allows you to turn on the engine.

It is usually located on the steering column, behind the steering wheel. The ignition lock cylinder works with the ignition switch, which is an electrical device that sends power to the starter motor and other components of your car.

The ignition lock cylinder and the ignition switch are connected by a metal rod or a cable.

There are several reasons why you might need to remove the ignition lock cylinder from your Chevy without a key. For example:

  • You lost your key and you don’t have a spare one.
  • Your key broke inside the lock cylinder and you can’t get it out.
  • Your lock cylinder is worn out or damaged and it doesn’t turn smoothly or at all.
  • You want to replace your lock cylinder with a new one for security reasons or personal preference.

Whatever the reason, removing the ignition lock cylinder from your Chevy without a key is not as hard as it sounds. You just need some basic tools and some skills.

What Tools Do You Need to Remove an Ignition Lock Cylinder Without a Key?

To remove an ignition lock cylinder without a key, you will need the following tools:

  • A flat-head screwdriver
  • A Phillips-head screwdriver
  • A small hammer
  • A drill and drill bits
  • A pin punch or a nail
  • A new ignition lock cylinder

You can find these tools at any hardware store or online. Make sure that the new ignition lock cylinder matches your car model and year.

How to Remove an Ignition Lock Cylinder Without a Key: Two Methods

There are two main methods to remove an ignition lock cylinder without a key: using a screwdriver and hammer, or using a drill. Both methods are effective, but they have some pros and cons. Here are the steps for each method:

Method 1: Using a Screwdriver and Hammer

This method is easier and faster than using a drill, but it may damage your steering column or other parts of your car. Use this method at your own risk.

  • Disconnect the negative battery cable from your car battery. This will prevent any electrical shocks or short circuits while you work on the ignition lock cylinder.
  • Remove the steering wheel cover by unscrewing the screws with a Phillips-head screwdriver. You may need to use a flat-head screwdriver to pry off the cover gently.
  • Locate the hole on the side of the steering column where the lock cylinder is inserted. You should see a metal pin inside the hole that holds the lock cylinder in place.
  • Insert a pin punch or a nail into the hole and tap it lightly with a hammer until the metal pin pops out. You may need to wiggle the steering wheel back and forth to release the pin.
  • Pull out the lock cylinder with a flat-head screwdriver. You may need to turn the screwdriver slightly to align the lock cylinder with the hole.
  • Replace the lock cylinder with a new one by inserting it into the hole and pushing it until it clicks into place.

Method 2: Using a Drill

This method is more precise and less risky than using a screwdriver and hammer, but it takes more time and skill. Use this method if you want to avoid damaging your car.

  • Disconnect the negative battery cable from your car battery.
  • Remove the steering wheel cover by unscrewing the screws with a Phillips-head screwdriver.
  • Locate the hole on the side of the steering column where the lock cylinder is inserted.
  • Use a drill and drill bits to drill out the metal pin that holds the lock cylinder in place. Be careful not to damage the wires or other components inside the steering column.
  • Pull out the lock cylinder with a flat-head screwdriver.
  • Replace the lock cylinder with a new one by inserting it into the hole and pushing it until it clicks into place.

How to Start Your Car Without a Key: Two Methods

If you don’t have a key for your ignition, you can try to start your car by using a screwdriver or a jumper wire. However, be aware that this may damage your ignition system or trigger your car alarm, so do it at your own risk. Here are two possible methods:

Method 1: Using a Screwdriver

  • Insert a flat-head screwdriver into the ignition switch and turn it as if it were a key. You may need to wiggle it or apply some force to turn it.
  • If the screwdriver doesn’t work, you can try to drill out the lock cylinder with a drill and drill bits. Be careful not to damage the wires or other components inside the steering column.
  • Once you have drilled out the lock cylinder, you can insert the screwdriver again and turn it to start your car.

Method 2: Using a Jumper Wire

  • Locate the starter relay under your hood. It should be in a fuse box near your battery or on the firewall.
  • Identify the terminals on the starter relay that are labeled 30 and 87. You can use a multimeter or a test light to check which terminal is which.
  • Connect one end of a jumper wire to terminal 30 and the other end to terminal 87. This will bypass the ignition switch and send power directly to the starter motor.
  • Turn on your car accessories, such as your radio or lights, by turning the ignition switch to ON position.
  • Touch the jumper wire briefly to start your car. Be careful not to touch any other wires or metal parts with the jumper wire.

Conclusion

In this article, we have shown you how to remove the ignition lock cylinder from your Chevy without a key, and how to start your car without a key.

These methods may help you in case of an emergency, but they are not recommended for regular use.

If you have lost your key or want to change your ignition lock cylinder, it is better to contact a professional locksmith or dealer for assistance.

They can provide you with a new key or a new lock cylinder that matches your car and ensures its security.

We hope you found this article useful and informative. If you have any questions or comments, please feel free to leave them below.

Also if you enjoyed this article and want to learn more about Chevrolet makes and history, don’t forget to check out our website for more interesting and informative content.

Leave a Comment